Jumo 705015 mTRON T - Relay Module 4-Ch. Operating Manu Instrukcja Użytkownika

JUMO mTRON TMeasuring, Control, and Automation SystemRelay Module 4-ChannelB 705015.0Operating Manual2013-06-18/00575604

1 Introduction101.3.4 DisposalDisposing of the deviceDisposing of the packaging materialThe entire packaging material (cardboard packaging, inserts, p

111 Introduction1.4 Identifying the Device Version1.4.1 NameplatesPositionThe nameplate (B) is affixed to the module case.An additional nameplate with

1 Introduction12Fabrication no. (F-Nr)Among other things, the fabrication number contains the date of production (year/week).Example: F-Nr = 007003380

132 Description2.1 Brief descriptionThe relay module provides four relay outputs controlled through the system bus by digital sig-nals (assigment in t

2 Description14

153 Installation3.1 General information on installation/dismountingMounting siteAll modules have protection type IP20 and are only intended for use in

3 Installation16Minimum distances3.2 Installation/dismounting on DIN railAll modules in the system are intended for installation on a DIN rail accordi

173 InstallationInstallation, using the example of a multichannel controller module 705010Example installationProcedure:(A) (A1)(A2)Step Activity1 Mou

3 Installation18Dismounting, using the example of a multichannel controller module 705010Removing the multichannel controller module from the DIN rail

193 Installation3 Move the modules (B) on the right next to the multichannel controller module that is to be replaced (A) a minimum of 20 mm to the ri

3 Installation203.3 Replacing module inserts3.3.1 Input/output modulesReplacement of a module insert, using the example of a multichannel controller m

213 InstallationRemoving the module insertMounting the module insertCAUTION!Only module inserts of the same type may be used for the replacement.Other

3 Installation223.4 Dimensions

234 Electrical connection4.1 Installation notesQualification of personnel• Work on the modules must only be carried out to the extent described and, l

4 Electrical connection24References to other information• The electromagnetic compatibility meets the standards and regulations cited in the techni-ca

254 Electrical connection4.3 Connection diagram4.3.1 Display and connection elementsCAUTION!At maximum load, the temperature may exceed 60 °C at the t

4 Electrical connection264.3.2 Relay outputs4.4 Functional testThe voltage supply must be tested on completion of the electrical connection:StartupThe

275 Operation5.1 Display and connection elements(1) Status displays (LED):P = Voltage supplyS = Status1 to 4 = Relay outputs (LED is lit: Active)(2) V

5 Operation285.2 LED displays"P" LED (Power)The LED is permanently lit in green if the module is being supplied with voltage."S" L

295 Operation5.2.2 System states and errorsThe following table lists all the system states and errors that are indicated by the "S" LED (Sta

3Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51.1 Available tec

5 Operation30

316 Configuration6.1 Digital outputsFour digital outputs (relay 1 to 4) are available.The digital outputs are exclusively driven by external inputs (N

6 Configuration326.2 NV connecting listThe NV connecting list is used to link external inputs (NV_...) of the relay module to signals from other modul

336 ConfigurationStatus after change of configurationThe connections are available immediately.Behavior after power onThe connections are available im

6 Configuration34Binary linking Binary linking 1 to 8 Result of binary linking 1 to 8PLC Binary output 9 to 32 Signal of PLC digital output 9 to 32 Bi

356 ConfigurationAlarms/ FaultsCAlarm/Fault System collective alarm or system fault (cen-tral processing unit and modules)CAlarm/Fault ackn. System co

6 Configuration36Multichannel controller moduleController C01ManualMode to C04ManualModeManual mode active for controller channel 1 to 4C01TuneActive

376 ConfigurationAnalog input module 4-channelAnalog inputs AI01Alarm1 to AI04Alarm1 Alarm signal 1 of analog input 1 to 4AI01Alarm2 to AI04Alarm2 Ala

6 Configuration38

397 Online parameters7.1 Calibrate / test7.1.1 Digital outputSetup dialogParameterTIP!An active connection between the setup program and the central p

Contents45 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275.1 Display and c

7 Online parameters407.1.2 VersionsSetup dialogThis dialog displays the module versions.

418 Appendix8.1 Technical data8.1.1 Outputs8.1.2 Electrical data8.1.3 Case and ambient conditions4 relay outputs (changeover contact)Switching capacit

8 Appendix428.1.4 Approval/approval marksApproval mark Testing agency Certificate/certifica-tion numberInspection basis Valid forc UL us Underwriters

JUMO GmbH & Co. KGStreet address:Moritz-Juchheim-Straße 136039 Fulda, GermanyDelivery address:Mackenrodtstraße 1436039 Fulda, GermanyPostal addres

51 Introduction1.1 Available technical documentationThe documents specified below are available for the measuring, control, and automation sys-tem.1.1

1 Introduction61.1.4 Special modules1.1.5 Operating, visualization, recording1.1.6 Power supply unitsProduct Type of documentation No. Printed PDF fil

71 Introduction1.2 Safety information1.2.1 Warning symbols1.2.2 Note signsDANGER!This symbol indicates that injury to persons caused by electrical sho

1 Introduction81.2.3 Intended useThe modules described are intended for measuring, control, and automation tasks in an indus-trial environment, as des

91 Introduction1.3 Acceptance of goods, storage, and transport1.3.1 Checking the delivery• Ensure that the packaging and contents are not damaged • Ch